| Titanium Turbo Shield | ||
|
Custom fit T3, T4 & T6 Titanium Turbo Shields, with LR Technology, provide the ultimate means of reducing turbo lag while serving as a
superior heat barrier - shielding and protecting engine components, hoods and painted surfaces while offering a very cool and unique looking
carbon fiber look. Made from pulverized volcanic rock that is strained into a fiber material, Titanium Turbo Shields can withstand direct
heat up to 1800°F and 2500°F of radiant heat.
Retaining more heat in the turbine means less damaging underhood heat, resulting in cooler air intake temperatures and boost in horsepower. Stronger and more durable than other turbo blankets or shields, Titanium Turbo Shields include a hi-temp rated silica insulation padding under a tight outer layer for extra protection against extreme turbo-generated heat. |
|
|
|
|
|
| Part # | Description | |
| DEI 010140 | T-3 Shield Only | |
| DEI 010141 | T-3 Shield Kit | |
| DEI 010144 | T-4 Shield Only | |
| DEI 010145 | T-4 Shield Kit | |
| DEI 010146 | T-6 Shield Only | |
| DEI 010147 | T-6 Shield Kit | |
| DEI 010148 | T-25 / T-28 Shield Only | |
| DEI 010149 | T-25 / T-28 Shield Kit | |
| Versa-Shield | |
|
Constructed using an aluminized reflective material along with a high temperature rated glass fiber insulation barrier, Versa-Shield is capable of reflecting up to 2000˚F of radiant heat. It is ideal for protecting starters and solenoids from potential failure caused by extreme heat and has multiple uses such as protecting master cylinders, cool cans, distributors, fuel pumps, and electrical boxes to name a few. To use, simply wrap desired component with Versa-Shield and trim excess material. Edges attach to itself using a hook & loop edge closure design. In most cases, there is no need to remove component when installing Versa-Shield. |
|
|
| Part # | |
| DEI 010402 | |
| Turbo Insulation Kit | ||
| Turbo Insulation Kits are designed to fit all turbochargers, from domestic and sport compacts to diesels and commercial vehicles. It is designed to reduce turbo lag and underhood temperatures for a cooler air charge. By protecting underhood components from unwanted heat, Turbo Insulation Kits can improve performance and add additional horsepower. |
|
|
|
|
|
| Part # | ||
| DEI 010113 | ||
| Cell Saver - Battery Insulation Kit | ||
|
Cell Saver is the ideal protection for any battery. Batteries are very susceptible to heat and vibration that could cause premature failure and hazardous leaks. Cell Saver is very capable of damping vibration, and will absorb and neutralize any damaging leaky battery acids. This kit is easy to install since the excess material can be trimmed to accommodate batteries of most sizes and shapes and its material is capable of withstanding radiant temperatures up to 2000°F. | |
|
|
|
| Part # | Description | |
| DEI 010480 |
Includes 40" x 7" insulation material, 12" x 7" treated base mat and edge sealing tape |
|
| Aluminized Plug Wire Sheath | ||
| DEI Aluminized Plug Wire Sheaths are made from a hi-temp glass fiber fabric that is bonded to reflective aluminized material. They were designed as an inexpensive way to protect specific spots on ignition wires and boots from heat sources. By reflecting 90% of radiant heat, Aluminized Plug Wire Sheaths reflect radiant heat to prevent wires and boots from burning or cracking, which could lead to arcing, engine misfire and costly damage. |
|
|
|
|
|
| Part # | Description | |
| DEI 010409 | 3/4" Diameter x 6" Long (4 to a pack) | |
| Cool Cover - Air Tube Cover Kit | ||
|
This Cool Cover/Air Tube Cover Kit is designed to prevent air tubes from becoming heat sinks. Made of heat treated fiberglass with a reflective coating, Cool Cover reflects radiant heat away from air tubes and promotes a cooler, denser and more powerful air charge. With a unique, full length hook & loop closure design, Cool Cover can be removed in seconds without the any need for hand tools - Easy ON for GO – Easy OFF for SHOW! | |
|
||
| Part # | Description | |
| DEI 010417 | Includes 36" x 14" insulation material, 2" x 24" strip of heat reflective sealing tape | |
| Motorcycle Fuel Tank Cover | ||
| Just as racers use tire warmers to maintain tire temperatures between sessions, it’s equally important to maintain stable fuel temperatures. Hot fuel results in less HP, increased fuel pump stress, and the increased risk of vapor lock. The DEI slip-on fuel tank cover is made from a 2mm felt backed Mylar material and is capable of reflecting up to 90% of the sun’s heat. This helps prevent the fuel in the tank from “baking in the sun” between green flags. Simply cinch the draw string and your bikes fuel will stay nice and cool between races. Elastic edges ensure a snug fit, no matter what brand you ride. |
|
|
|
||
| Part # | Description | |
| DEI 010465 | Universal fit with draw string to secure cover | |
| EGR Cover Pipe Heat Shield for Corvette 1985-1991 | ||
|
Protect 1985 through 1991 Corvette L98 EGR systems and nearby under hood components from damaging heat with the proper EGR Pipe Cover. With DEI’s sewn-in hook & loop edges, installing the EGR cover is a simple, quick and straightforward replacement without removing the EGR pipe. Just wrap the cover around EGR pipe and close edges. Trim off any excess material if necessary. It’s that easy.
EGR Covers are made of a high temperature rated glass fiber fabric bonded to a heat reflective aluminized outer facing. Capable of handling direct heat up to 500°F and 2000°F radiant, EGR Covers also provide protection from oil, grease and chemical spills. |
|
| Part # | Description | |
| DEI 010387 | 11.5" x 4.5" - 1985-88 (some 1989) | |
| DEI 010388 | 15" x 4.5" - 1990-91 (some 1989) | |
| DEI 010389 | 4.5" x 4.5" - 1987-91 | |